Assessment of the upper and lower levels of permissible strains in the manufacture of sheet and thin-walled parts based on the forming limit diagram
Forming limit diagrams (FLDs) are currently widely used in the analysis of sheet metal forming without destruction and in assessing the technological capabilities of metal forming. This paper is devoted to the FLD-based assessment of the maximum and minimum limiting strains of the forming of thin-walled workpieces. Theoretical analysis of well-known criteria is used, including the criteria for the occurrence of scattered and localized necks, the so-called energy (static) criteria, as well as the criterion of abrupt local thinning of the sheet, the so-called kinematic criterion. This paper considers a two-way analysis of the forming limits of thin-walled workpieces according to FLDs, which allows one to determine the upper and lower estimates of the limiting strains of the forming. The analysis is based on the FLD study results obtained by various authors and published both in Russia and abroad. The presented research results can be used as a first-order analysis tool for evaluating and predicting the technological capabilities of the molded material in the manufacture of thin-walled parts. They are also relevant to metal processing by pressure and plastic forming of thin-walled sheets.
Keywords
forming limit diagram,
Hill-Swift criterion,
Storen-Rice criterion,
upper and lower estimates of the forming limitsAuthors
| Feoktistov Sergey I. | Komsomolsk-on-Amur State University | serg_feo @mail.ru |
| Andrianov Ivan K. | Komsomolsk-on-Amur State University | ivan_andrianov_90@mail.ru |
Всего: 2
References
Stoughton T.B. General forming limit criterion for sheet metal forming // International Journal of Mechanical Science. 2000. № 42. Р. 1-27.
Казанцев А.В. Основы LS-DYNA. Диаграмма предельных деформаций (FLD). Создание и верификация моделей поведения материалов : метод. пособие. Пермь, 2018. URL: http://dpm.pstu.ru>images/R/НЖ>_Основы_LS-DYNA_v1.1.pdf.
Sanay B. Prediction of Plastic Instability and Forming Limits in Sheet Metal Forming : A Thesis Submitted to the Graduate School of Natural and Applied Sciences of Middle East Technical University in Partial Fullfilment of the Requirements for the Degree of Master of Science in Mechanical Engineering. 2010.
Paul S.K. Theoretical analysis of strain- and stress-based forming limit diagrams // Strain Analysis. 2013. № 48 (3). P. 177-188.
Marciniak Z., Kuczynski K. Limit strains in the processes of stretch-forming sheet metal // International Journal of Mechanical Science. 1967. № 9. P. 609-620.
Marciniak Z., Kuczynski K., Pokora T. Influence of the plastic properties of a material on the forming limit curve for sheet metal in tension // Int J Mech Sci. 1973. № 15. P. 789-805.
Nakazima K., Kikuma T. Forming Limits under biaxial stretching of sheet metals // Testu-to Hagane. 1967. № 53. P. 455-458.
Nakazima K., Kikuuma T., Hasuka K. Study on the formability of steel sheets // Yawata Tech nical Report. 1968. № 264. P. 141-154.
Изосимова С.В. Исследование влияния формы заготовки на точность построения диа граммы предельных деформаций // Студенческая научная весна 2013: Машиностроительные технологии : всерос. науч.-техн. конф. студентов. 2013. URL: http://studvesna.ru/db_files/articles/810/article.pdf.
ISO 12004-2:2021. Metallic materials - Determination of forming-limit curves for sheet and strip - Part 2: Determination of forming-limit curves in the laboratory.
Swift H.W. Plastic instability under plane stress // Journal of the Mechanics and Physics of Solids. 1952. № 1. P. 1-18.
Hill R. On discontinuous plastic states with special reference to localized necking in thin sheets // Journal of the Mechanics and Physics of Solids. 1952. № 1. P. 19-30.
Storen S., Rice J.R. Localized necking in thin sheets // Journal of the Mechanics and Physics of Solids. 1975. № 23. P. 421-441.
Чумадин А.С. Об одном подходе к расчету предельного деформирования при листовой штамповке // Кузнечно-штамповочное производство. 1990. № 6. С. 10-13.
Чумадин А.С. Методы расчета предельных деформаций в операциях листовой штамповки : учеб. пособие. М. : Изд-во МАТИ, 2002.
Чумадин А.С. Теория и расчеты процессов листовой штамповки : (для инженеров). 2-е изд. М. : Экспосервис «ВИП», 2014.
Marciniak Z., Kuczynski K., Pokora T. Influence of the plastic properties of a material on the forming limit curve for sheet metal in tension // International Journal of Mechanical Science. 1973. № 15. P.789-805.
Marciniak Z., Kuczynski K. Limit strains in the processes of stretch forming sheet steel // Journal of the Mechanics and Physics of Solids. 1967. № 1. P. 609-620.
Филимонов В.И., Мищенко О.В. Теория обработки металлов давлением : учеб. пособие. Ульяновск : УлГТУ, 2012.
Stoughton T.B., Zhu X. Review of theoretical models of the strain-based FLD and their relevance to the stress-based FLD // International Journal of Plasticity. 2004. № 20. P. 1463-1486.
Малинин Н.Н. Прикладная теория пластичности и ползучести. М. : Машиностроение, 1975.
Шалин Р.Е. Авиационные материалы : справочник для инженерно-технических и научных работников : в 9 т. / под общ. ред. Р.Е. Шалина. 6-е изд. перераб. и доп. М. : ВИАМ, 1982. Т. 4: Алюминиевые и бериллиевые сплавы, ч. 1: Деформируемые алюминиевые сплавы и сплавы на основе бериллия.
